We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.
A new paper published in the Energies journal seeks to evaluate the most commonly employed methods of repairing these wind turbine blades, investigating their effectiveness, robustness following repair, and their tendency to become damaged again, following repair.
Study: Technologies of Wind Turbine Blade Repair: Practical Comparison . Image Credit: Jacques Tarnero/Shutterstock.com
There are an estimated 700,000 wind turbine blades in operation around the world, with an average of 3800 annual blade failure incidents requiring minor repairs, major repairs, or complete replacement.
The relatively high cost of wind energy is partially due to the cost and complexities of maintaining and repairing the wind turbines themselves, so investigation into and optimization of these repairs could be key to making wind energy more cost-effective and widely available.
Schema of damaged plate (a), photos of plate (b) and of repair procedure (c). Image Credit: Mishnaevsky L Jr et al., Energies
This work is especially relevant for a number of reasons. It is anticipated that the global market for wind power will reach as much as 69700 megawatts come 2027, with the European Union seeking to increase its wind power capacity from 180 gigawatts to 451 gigawatts by 2030 and the U.S. currently working towards generating 30 gigawatts of offshore wind power by 2030.
Reports have shown that onshore wind farm operators spent approximately USD 15 billion on operations and maintenance costs, with as much as 57% of these costs related to unplanned repairs.
Another important factor is the age of many wind turbines, with many of these being installed at the start of the 21st century beginning to deteriorate, requiring more frequent and expensive repairs. These aging turbines, coupled with the sheer number of new turbines coming online over the coming years, will increase the operations and maintenance burden significantly.
The paper’s authors focused on the structural repair of damaged and broken wind turbine blades, using a series of composite plates to simulate these and using a series of tests to evaluate their post-repair properties.
Photo of repaired plate, and geometry of samples to be cut out. Image Credit: Mishnaevsky L Jr et al., Energies
Their goal was to provide wind turbine service companies and management teams with a practical approach to selecting and evaluating repair technologies based on their specific needs, as well as evaluating the performance of the technologies under semi-real conditions and feeding this back to adhesive and equipment developers.
A total of six different technologies were used to repair damaged laminates under comparable conditions, with the repaired samples investigated using microscopic X-ray tomography and tested under tensile static and fatigue tests to evaluate their performance and characterize their failure mechanisms.
Hand layup lamination was evaluated – a conventional approach that involves an engineer putting resin on the laminate and hand-rolling this. Vacuum repair with hand layup saw vacuum applied following hand layup, and another version of this method was used with dry laminate put on the repair and vacuum. Two types of ultraviolet repair were tested, as well as high-temperature thermal curing.
The study’s findings were in-depth and interesting. It was determined that stiffer repair structures with lower maximum stress could be achieved by using repair techniques with applied vacuum, while high-temperature curing resulted in higher maximum stress but softer structures. Average stiffness and high strength were found to be achievable using ultraviolet curing technologies.
One notable disadvantage of the hand layup approach, both with and without vacuum, was the formation of many voids in the repaired part. There was also evidence of residual stresses in a number of samples after bending, suggesting that the repair techniques led to the creation of internal and thermal stresses.
Cracks identified in samples (a) HTC and (b) UV1. The white dotted line indicates the interface between the scarf and the repair, and the red arrows indicate cracks. Image Credit: Mishnaevsky L Jr et al., Energies
The vacuum hand layup technology leads to the formation of a lot of voids in the repaired part, more than all other technologies. The hand layup without vacuum also creates long elongated voids, probably related to badly bonded fibers. In terms of fatigue lifetime, it was noted that vacuum hand layup technology demonstrated the lowest lifetime, UV and high-temperature curing demonstrated average results, while handheld UV curing offered the best performance.
The study offers a promising start to this relatively new area of research, and one which is set to become increasingly important as renewable energy – and most notably wind power – becomes a more central component of global energy production. The optimization of repair technologies and improvements in their effectiveness will be key to minimizing any planned or unplanned downtime of wind turbines and, therefore, maximizing their potential for energy generation.
Mishnaevsky L Jr., Frost-Jensen Johansen N, Fraisse A, Fæster S, Jensen T, Bendixen B. Technologies of Wind Turbine Blade Repair: Practical Comparison. Energies. 2022; 15(5):1767. https://www.mdpi.com/1996-1073/15/5/1767
Disclaimer: The views expressed here are those of the author expressed in their private capacity and do not necessarily represent the views of AZoM.com Limited T/A AZoNetwork the owner and operator of this website. This disclaimer forms part of the Terms and conditions of use of this website.
Adrian Brian Thompson is a freelance writer, educator, and creative based in Todmorden, United Kingdom. His diverse industry experience ranges from frontline youth and support work to marketing, website development, copyediting, event production, and project management across a range of sectors. Adrian holds an MA with Distinction in Music Industry Studies from The University of Liverpool, and his wider academic background spans a range of disciplines, including social work, social sciences, politics, and information technology
Please use one of the following formats to cite this article in your essay, paper or report:
Thompson, Adrian. (2022, March 01). What Technologies are Required to Repair Wind Turbine Blades?. AZoM. Retrieved on March 12, 2022 from https://www.azom.com/news.aspx?newsID=58389.
Thompson, Adrian. "What Technologies are Required to Repair Wind Turbine Blades?". AZoM. 12 March 2022. <https://www.azom.com/news.aspx?newsID=58389>.
Thompson, Adrian. "What Technologies are Required to Repair Wind Turbine Blades?". AZoM. https://www.azom.com/news.aspx?newsID=58389. (accessed March 12, 2022).
Thompson, Adrian. 2022. What Technologies are Required to Repair Wind Turbine Blades?. AZoM, viewed 12 March 2022, https://www.azom.com/news.aspx?newsID=58389.
Do you have a review, update or anything you would like to add to this news story?
AZoM speaks to Michael Jewett, a researcher at Northwestern University, about a novel process using bacteria to capture CO2 and convert it into the useful commercial chemicals acetone and isopropanol. This could bring us closer to a circular bioeconomy in the chemical sector.
In this interview, AZoM talks to Anna Walkiewicz, Applications Specialist at Quorum Technologies, about sample coating and how it can help improve SEM imaging.
In this interview, AZoM talks to Anna Walkiewicz, Applications Specialist at Quorum Technologies, about sample coating and how it can help improve SEM imaging.
Discover the mechanical rotary level indicator, model BMR-100.
Superior Sensor’s ND Middle Pressure Series utilize Superior Sensor’s advanced Nimblesense technology, making them extremely accurate, reliable, and precise.
TESCAN’s UniTOM HR is the only micro-CT system that allows sub-micron spatial resolution as well as high temporal resolution dynamic CT, for all your materials science and earth science needs.
This article provides an end-of-life assessment of lithium-ion batteries, focusing on the recycling of an ever-growing amount of spent Li-Ion batteries in order to work toward a sustainable and circular approach to battery use and reuse.
This article provides an overview of the materials that are used to produce photovoltaic cells for the production of renewable energy, as well as new research that proposes the use of novel materials.
This article considers laser-based 3D printing, or additive manufacturing, looking at different types of lasers in the fabrication process.
AZoM.com - An AZoNetwork Site
Owned and operated by AZoNetwork, © 2000-2022